Hi,
Could you please advise what settings you used to convert the font in EVE Asset Builder and also which version of the EAB you use?
Best Regards, BRT Community
- May 19, 2024, 03:20:55 PM
- Welcome, Guest
News:
Welcome to the Bridgetek Community!
Please read our Welcome Note
Technical Support enquires
please contact the team @ Bridgetek Support
Please refer to our website for detailed information on all our products - Bridgetek - Bridging Technology
71
on: March 16, 2024, 06:08:01 PM
|
||
Started by Craggan - Last post by BRT Community | ||
72
on: March 16, 2024, 01:10:26 PM
|
||
Started by Craggan - Last post by Craggan | ||
Hi there,
is there a failure in the font converter? When i create UNICODE fonts bigger than 18 the distance between the letters are to big, please see attachment. In this case font "Ubuntu". Or am i wrong? |
73
on: March 16, 2024, 01:00:26 PM
|
||
Started by TreeOone - Last post by Craggan | ||
Just testing Unicode strings.
The cmd_text() row also floods the screen. One word less at the end and it works, but the screen flickers. EVE_cmd_setfont2( 1, EVE_RAM_G, 0 ); cmd_text( 10, 10, 1, 0, "\u00D6sterreicher \u00E4rgern sich \u00FCber \u00E4gypter"); 20 rows with 2 or 3 Umlauts in 1 line are OK. More then 3 Umlauts in 1 line kill. |
74
on: March 12, 2024, 06:31:51 PM
|
||
Started by TreeOone - Last post by Rudolph | ||
I have a RVT70HSBNWC00-B and I am using the exact same controller board with it, I only modified the regulator for the backlight to only do 5V since this is what the RVT70HSBNWC00-B requires while the RVT101HVBNWC00-B needs 7...14V for the backlight.
So on my side the same controller on the same board and therefore the exact same software using the same compiler etc. With the 1024x600 RVT70HSBNWC00-B I can increase the NOPs to 1794 which results in a display list of 7272 bytes. One more and it starts to flicker. |
75
on: March 12, 2024, 04:34:02 PM
|
||
Started by TreeOone - Last post by BRT Community | ||
Hi,
We will test out and investigate this also and keep you updated, thanks for your additional test results Rudolph, Best Regards, BRT Community |
76
on: March 11, 2024, 09:19:33 PM
|
||
Started by TreeOone - Last post by Rudolph | ||
That is interesting, I converted that code to work with my library to see if your library is at fault.
Code: [Select] void TFT_display(void) And like this I can set SENDNOPS to 1003 with a resulting display list of 4784 bytes before the display glitches out. Commenting out the three buttons I can set SENDNOPS to 1334 which is a display list of 5432 bytes. So I can go higher, but I can not use the full 8kiB of the display list either. One thing that could go wrong is that the CMD-FIFO is getting full since it only has 4kiB. But that is not the issue, I am using individual commands in this example, no DMA, chip-select low, address, command, chip-select high. It should not be possible to throw in more in the FIFO like this than the co-processor can handle. But to make sure I slowed down the SPI and also added a busy-wait for the FIFO to be empty in the loop - makes no difference. In a different project that really is putting stress on the BT817 with thousands of line-strip segments, I am using DMA and fill the FIFO with 3676 bytes with a resulting display list of 6108 bytes - but it glitches out after a minute or less. When I put in less it runs longer without issue - and by less I mean less iterations, like "only" using 36 points per line strip instead of 64. It looks like my BT817 is overheating, pretty sure it is not, but it looks like it is. Oh, another observation out of a hunch, updating the display list less often seems to help as well, I am at 20Hz / 50ms now with 5672 bytes in the display list. This does not help with the program above though, the limit is still 1334 NOPs with a display list of 5432 bytes. |
77
on: March 11, 2024, 02:56:55 PM
|
||
Started by moiatto - Last post by BRT Community | ||
Hello,
Thank you for your question. We utilise the following LED backlight drivers on our development modules, maybe these would be suitable for your application: IS31BL3506A IS31BL3506B Best Regards, BRT Community |
78
on: March 11, 2024, 11:18:00 AM
|
||
Started by koyocik88 - Last post by BRT Community | ||
Hello,
Yes, the append technique in AN_340 is one of the best ways to do this, Which EVE device do you use? The BT817/8 also have a more advanced version of this where you can store sections of command list (as well as section of display list) and this can make it even easier However, the Append can be used on all EVE devices in any case if you use other models apart from BT817/8. We also have an example of the same technique as AN_340 where we draw the chart line and the numerical values here using append whilst the other static items are stored: https://brtchip.com/wp-content/uploads/Support/Documentation/Application_Notes/Modules/EVE/AN_356-FT800-Interfacing-I2C-Sensor-to-VM800P.pdf Best Regards, BRT Community |
79
on: March 11, 2024, 10:32:59 AM
|
||
Started by koyocik88 - Last post by koyocik88 | ||
Hello!
I'm trying to find a way how to update part of displayed screen (i.e. change only some values on displayed screen or status of displayed button). I don't want each time send whole display list. I found a document "APPLICATION NOTE AN_340 FT800_Optimising screen updates with Macro and Append" given by Bridgtech. In my example I want change only values for displayed labels. Could you advise me if gives other possibility how to update choose parts of the showed screen ? Code: [Select] void showScreen () Thank you in advance! |
80
on: March 11, 2024, 06:48:24 AM
|
||
Started by david - Last post by david | ||
Hi, did you get any new information about that compatibility topic?
|